Stamped Copper Busbar Links and Jumper Plates

Drawing-based flat, offset and bent copper interconnects for bolted power distribution assemblies.

Rate: US$ 19.50/Kg

Cable Glands India supplies stamped copper busbar links and jumper plates for switchgear, panelboards, distribution cabinets and industrial power assemblies. Request flat links, offset links, bent jumpers and slotted jumper plates against your drawing, material and finish specification. The sections below describe the interfaces that matter for fit, tooling review and first article approval.

Rate: US$ 19.50/kg

Send your drawing for a quotation · View Copper Stamped Parts

Product designs and application requirements

Flat links

Flat links connect mounting points on the same plane. Define hole centers from a common datum and show the bearing area around each hole. A narrow neck between adjacent holes can dominate the usable current path.

Include a dimensioned view of the mating component with the request for quotation. Mark the features that establish fit and the surfaces that actually touch in the finished assembly. This lets the tooling review separate the tolerances needed for fit from those needed for current transfer. It also helps establish whether first articles can be inspected with standard instruments or need a dedicated fixture. Where the customer provides both a model and a drawing, identify which revision controls and call out any dimensions that the model alone cannot communicate.

Offset links

A stepped link clears hardware or spans terminals at different heights. Give the finished step height and offset between mating faces. Include clearance for the tool used to install the bolts.

Provide nominal geometry and acceptance limits for the finished part. A formed component can measure differently when it is free on a bench and when it is restrained in an assembly. If the mounting condition controls fit, define the restraint and its location in the inspection plan. Review sample parts in the same orientation used during installation. Where the design has handed versions, include a view that makes the handedness unambiguous, since similar parts can be difficult to distinguish during incoming inspection or line-side picking.

Bent jumper plates

An angled jumper can change the direction of the current path inside an enclosure. Specify the inner bend radius, orientation and final angle. Check clearance to the enclosure and adjoining conductors across the full tolerance stack.

Review material and geometry together during die design. Copper grade, temper, thickness and bend direction influence how a formed feature behaves, so the material specification should travel with the dimensional drawing. If multiple grades are acceptable, identify them as approved alternatives and state whether each requires separate approval. A dimensional first article from one material should be traceable to its lot and temper. For repeat orders, retain that information so changes in material condition can be evaluated against the original qualification record.

Slotted links

A slot can accommodate installation variation along its long axis. Identify its orientation and the maximum permitted assembled offset. Check washer coverage and bearing area at both ends of travel.

Show the required finish in the same drawing package as the mechanical features. State whether the drawing dimensions apply before or after finishing. Identify measurement zones separately when an important surface lies inside a bend, around a pierced edge or on a recessed portion of the part. If the finish is specified by a customer standard, include the document and revision. This gives purchasing and quality teams a common basis for quoting, inspecting and releasing the parts, especially when different finishes share the same stamping tool.

Switchgear interfaces

Locate the link relative to mounting rails, insulation barriers and terminal fasteners. The assembly drawing can expose interferences that a standalone link drawing cannot show.

Ask the assembly team which operation sets the part position and which feature must stay clear during installation. A datum should reflect the way the part is seated or held in service wherever practical. Check that the chosen datum is also accessible for measurement. An assembly fit check can catch stack-up across multiple parts, while a dimensional report shows which feature contributes to the stack. Both records help if a future drawing change changes the fit of a component that previously passed incoming inspection.

Panelboard layouts

Parallel circuits can have different pitch requirements even when they share the same nominal conductor width. Identify phase, orientation and mounting pattern explicitly for each part number.

List the electrical and mechanical tests that will be run on the assembly and identify any sample requirements early. Current, force, temperature or retention targets should be tied to the actual mating hardware and test conditions. The stamping drawing can control geometry, material and surface condition. The assembly test establishes performance under the specified duty. When a customer needs documentation for design approval, agree which evidence comes from raw material records, which comes from stamped part inspection and which will be supplied by the assembly test program.

Contact lands

Keep critical contact lands clear of embosses, bend transitions and trim edges. If the whole link does not need tight flatness, zone the requirement around the joint.

Use a section view when important features are hard to read in plan view. Include bend reliefs, edge breaks or local changes in thickness where they affect clearance or strength. If an edge faces insulation, an operator or another critical surface, specify the edge treatment on that side. General deburring notes can be supplemented with explicit zones for special treatment. Agree on an inspection method that distinguishes a measurable burr from a rounded or polished edge, particularly if the part will be inspected after finishing.

Bolted joints

Specify the complete joint stack, including mating metal, washers and bolting arrangement. Joint performance depends on the assembled interface, its preparation and clamp load.

Include the expected ordering pattern when requesting a quotation. A prototype batch, a qualification run and a recurring production order can have different setups and inspection needs. If samples are needed ahead of production, indicate which checks they must support and when the mating components or fixtures will be available. Share likely lot sizes and annual demand so the tooling proposal reflects how the part will be made and replenished. Record separately any dedicated gauges, fixtures or special packaging included in the commercial scope.

Cross section

Document minimum section after holes, slots and forming operations. Where the link necks down, evaluate the smallest usable path in the actual installation.

State the allowed variation on the finished part and show which dimensions are basic or reference-only. Redundant tolerances can make a drawing harder to inspect and can obscure the dimensions that govern assembly. Where several features must line up together, define their relationship from common references. Review the proposed measurement method during sample approval. If different methods can produce materially different readings, agree which method controls acceptance and record any fixture pressure, support points or alignment steps needed for repeatable results.

Burr direction

Orient the burr away from the mating surface or insulating barrier where practical. If both faces must seat flush, identify edges that require secondary deburring.

Describe the condition in which the part will reach the assembly station. The finish may be accepted on a sample before packaging, while transport and bulk handling can affect its appearance or shape. Define surfaces that require separators, individual cavities or another form of protection. Include pack quantity and label requirements where parts feed directly to production. If the handling method changes between sample and production quantities, check that the production pack still preserves the features that were qualified on the sample.

Coining and surface condition

A locally coined land may help control a critical interface. Identify its footprint, allowable witness marks and finished thickness. Review whether the operation affects adjacent bends or holes.

Discuss part orientation during tool review. Bend direction, trim direction and the placement of carrier ties can affect which face carries a burr or tooling mark. Review candidate tie locations against critical surfaces and mating zones. Where witness marks are permitted, place them on the drawing or on an approved sample. Where they are restricted, identify the relevant surface and reason, such as sliding fit, insulation clearance or contact area. That detail helps evaluate the tooling proposal and gives inspectors an objective basis for acceptance.

Tooling and strip layout

A long, narrow blank may curl or twist after cut-off. Review carrier position, grain direction and available inspection support before approving the strip layout.

Treat revision control as part of the purchase specification. Use the same drawing number, revision and finish code on the quote, order, sample report and shipment label. Identify similar parts that must be segregated, including mirrored or differently plated versions. If a revision changes geometry or material, state the date or order from which the change applies and whether old stock can be used. A retained sample and a traceable inspection record can help reconcile dimensional differences found during assembly after a revision change.

Temperature rise review

Provide current duty, enclosure details, ambient conditions and the joint configuration for engineering review. Evaluate temperature rise on the finished assembly under representative loading.

Define approval at the feature level. A visual sample can establish an appearance limit, a dimensional report can document measured geometry, and an assembly trial can establish installation fit. Specify which evidence is required for each critical characteristic. If a dimensional feature is hard to measure without damaging the part, discuss destructive sampling or an agreed proxy during tool planning. Record how production samples will be taken and what action follows an out-of-tolerance result, including any need to segregate affected lots.

Mounting repeatability

Use fixture pins or an agreed measurement setup to validate hole position and overall profile. For bent jumpers, locate the part from its functional mounting plane.

Identify which dimensions are especially sensitive to material variation or press setup. A part that leaves the tool with an acceptable outline can still show changes in formed height, local twist or contact angle. Agree on a representative sampling plan across a run when those changes affect installation. Where the customer uses a check fixture, share its seating method and reference geometry with the manufacturer. Comparing the two inspection setups during sample approval can prevent disagreement when parts arrive at the assembly plant.

Finish boundaries

A finish callout should state whether contact faces, punched holes and cut edges must be plated. If masking is necessary, show the boundary and allowable transition.

Specify the surface condition needed at delivery, including any allowed handling residues and the method of protection after finishing. If the part will be joined or plated again downstream, communicate the cleaning and surface preparation requirements for that process. Agree whether appearance is assessed in natural light, under magnification or against a retained sample. The finish requirements should distinguish the surfaces that are visible in the final assembly from those whose surface condition affects electrical, mechanical or joining performance.

Packing flat and formed links

Separate formed parts so they cannot nest tightly or pry against adjoining links. Protect broad contact lands from rubbing, especially if the approved finish is susceptible to marking.

Finish the review with a clear list of release inputs. These typically include a current drawing, material and temper, finish specification, expected order quantities and acceptance criteria. Include a model or a sample where it resolves assembly details. For export shipments, identify packing, labeling and requested quality documents up front. This helps the quote reflect the actual scope and gives both purchasing and production teams a single specification to use when moving from prototype approval to repeat supply.

Comparing flat and offset links

Start with the two mounting planes and check access to the fasteners. A flat jumper can simplify inspection when the terminals line up. A stepped jumper can preserve joint positions where one terminal sits behind a cover or on a different mounting level. The step adds transition areas that must clear the surrounding hardware. Compare the bolting sequence and tool approach before releasing the design. For a family of similar links, use an approved table of hole pitches and offsets tied to individual drawings. Trial fitting in a representative cabinet lets the design team verify enclosure clearance, fastener access and joint seating together.

Technical specification checklist

Materials, manufacturing and order requirements

Copper grade and temper

Use the customer drawing to specify the copper grade and temper. C11000 ETP and C10200 oxygen-free copper can be considered when the design calls for high conductivity, subject to review of forming and joining requirements. A spring function may call for a higher-strength copper alloy and a validated working deflection. Material selection starts with the electrical duty, mechanical function, environment and joining process. Supply the exact purchase specification if a particular material certification, strip condition or direction of rolling must be preserved. For a design transferred from another supplier, include the existing material specification and approval history where available.

Strip thickness and bend feasibility

Give the nominal strip thickness and tolerance together with the final formed dimensions. The design should show internal bend radii and any features close to a bend line. Material displaced during forming can influence adjacent holes or slots, and a tight bend may require review of both material and tooling. Distinguish stock thickness from locally formed or coined thickness. For any feature that has to mate with another component, give the acceptable finished thickness at the point of engagement. If the drawing uses a generalized thickness note, identify the zones where a local deviation matters to the assembly.

Bare and plated finishes

Bare copper and tin, nickel or silver finishes can be discussed against the drawing. The request should say where the finish is needed, how thick it must be and whether a test or certificate is required. If the same part number has multiple finishes, identify a separate finish code so the quote and label remain clear. Review post-stamping coverage if cut faces or pierced holes are functional. Review prefinished strip when carrier handling or downstream assembly calls for a specific surface condition. For either route, communicate any restrictions on discoloration, exposed substrate or contact with packaging material.

Progressive or staged tooling

A repeat production job can use a progressive sequence of piercing, blanking, forming and cut-off operations where the geometry and quantities support that route. A staged process can be evaluated for sample lots or designs requiring individual operations. Tooling selection depends on strip utilization, form sequence, handling and inspection access. Before tooling release, identify the sequence most likely to preserve critical features. Discuss tool ownership, maintenance and storage on repeat programs if they are important to the sourcing agreement. Document any changes from the qualification method before the next run is released.

Drawing package and quotation

Send the drawing number and revision, model if available, material grade, temper, finish, sample quantity and annual usage. Include the mating interface if the geometry is controlled by a larger assembly. A quote can then separate the recurring part cost from tooling, inspection or packaging requirements. Identify any approval milestone that needs samples delivered before the production order. Where only a sample exists, use it to establish a review drawing and agree the dimensional and material requirements before release. That gives both the buyer and manufacturer a controlled reference for future replenishment.

First article inspection and production release

Use samples to review both measurable characteristics and actual assembly fit. Identify which dimensions, surfaces and test reports need formal approval. A first article record can carry the part number, material lot, tooling reference, finish and drawing revision so the approval can be traced. If a part is supplied with mating samples, record the revision and setup used for the trial. Production release should follow the agreed approval process. If the drawing changes before production, confirm which features require a new sample and update the order documents to point to the approved revision.

Incoming inspection and traceability

Agree how lots will be identified and how measurement results will be reported. A buyer may need the purchase order, drawing revision, quantity, finish and batch on the shipment label. Quality documentation should reflect the checks required for the part, such as dimensional results, raw material documentation or coating thickness reports. Identify any special sampling rules or record retention period when requesting the quote. If parts will be split into smaller packs downstream, use identification that can be carried into the assembly area. Retaining lot identity helps investigate a fit or finish issue without mixing production batches.

Commercial rate and order scope

The listed rate is US$ 19.50/kg. Request an itemized quotation for the drawing and order quantities so that tooling, sample submission, finish, inspection, packing and delivery terms can be confirmed for the project. Include the expected call-off pattern if the total volume will be ordered in several releases. State the destination and any requirements for labels or supporting documents. For repeat programs, identify the approved part revision and any finish variants on the order. This keeps price discussions tied to the same supply scope and avoids treating differently configured parts as interchangeable.

Frequently asked questions

What busbar links and jumper plates can I request?

The product family covers flat links, offset links, bent jumpers and slotted jumper plates. These configurations are used in switchgear, panelboards, distribution cabinets and industrial power assemblies. Supply the specific drawing and application when asking for pricing. Where a part combines several features, identify the critical mounting, mating or joining surfaces so they can be assessed together during the tooling review. A representative sample or assembly view is especially helpful when adjacent hardware controls the final shape.

How much do these stamped copper parts cost?

The listed rate is US$ 19.50/kg. Send quantities, finish and drawing requirements for an itemized quote. The proposal can identify any project-specific tooling, sample inspection, packaging and delivery charges. For repeated releases under a single program, include the expected order schedule so the quote reflects the lot sizes and packing configuration actually required.

Which information should I include with a drawing?

Include the controlled revision, material, temper, finish, critical dimensions and expected production volumes. Where possible, include the mating hardware or an assembly model. An assembly reference helps review installation direction, clearance and orientation. Include the approved inspection method if a feature is checked under restraint or in a dedicated fixture.

Can I request plated copper stampings?

Yes. Discuss bare, tin, nickel or silver finishes with the drawing and service conditions. Specify the surfaces requiring coverage, thickness acceptance limits and how the coating is checked. If exposed cut edges or tooling marks are restricted, identify their limits on a drawing or approved reference sample. Keep finish variants traceable by a separate part or finish code.

Can I order samples before a production release?

Request the sample quantity and approval documentation during quotation. Discuss whether the samples need to come from production tooling and whether they must carry the production finish. A sample review can include dimensional inspection, mating fit and any tests specified for the assembly. Agree how revisions will be documented if a sample leads to a geometry change.

How are tolerances agreed?

The drawing and approved inspection plan establish tolerance limits for each part. Review features such as holes, bends and functional surfaces against the installation condition. Where dimensions depend on support or clamping, agree on the measurement setup. The tolerance review should identify which features require a dedicated gauge and which can be checked with routine instruments.

What documents can I request with the order?

List the documents required for the project, such as a dimensional report, raw material certification, finish inspection or a first article report. Confirm the document format, frequency and traceability information during quotation. If the receiving site uses a specific approval format or labels, share those requirements along with the drawing and purchase specification.

How do I qualify the part for my equipment?

Start with dimensional and material verification, then inspect representative parts installed with the actual mating components. Define the conditions for electrical or mechanical testing, including the applicable loads and environment. Validate the finished assembly against your engineering requirements and record the approved part and drawing revision before releasing recurring orders.

Request a quote for busbar links and jumper plates

Email sales@cableglandsindia.com with your drawing, finish, quantities and required delivery date. Include any sample approval, packaging and inspection requirements. The quotation will define the manufacturing and delivery scope for your part.

Related copper stamping products

• Copper Stamped Parts
• Stamped Copper Transformer Connector Tabs and Lead Straps
• Stamped Copper Electrical Contacts and Coined Contact Pads
• Stamped Copper Blade Terminals and Open-Barrel Crimp Contacts
• Copper Pressed and Deep-Drawn Parts